Attach and assign.
Place each sensor on a suitable magnetic surface on its machine. Keep it away from water, excessive heat and moving parts. Assign one as Washer and the other as Dryer during setup.
From first pairing to the first finished load, here’s the setup overview and help for common questions.
Place each sensor on a suitable magnetic surface on its machine. Keep it away from water, excessive heat and moving parts. Assign one as Washer and the other as Dryer during setup.
In the app, tap Add device and allow Bluetooth. A new sensor shows PAIR ME on its screen by itself. To pair one again later, open its menu, choose Pair new phone and hold to confirm. It shows PAIR ME for 5 minutes. Keep your phone nearby while pairing.
Provide a 2.4 GHz Wi-Fi network that reaches both machines. After setup, the devices use Wi-Fi to send events to the service.
With the machine off, open the sensor’s menu and choose Calibrate. When the screen says “Machine OFF”, hold to start and don’t touch it for about 13 seconds. When it says “Start the machine”, start it. Once it’s running, hold again. It measures for 30 seconds and shows CALIBRATED. If it says TOO SIMILAR, move the sensor closer to the drum, like the top or front near it, and hold to try again. To redo it later, choose Recalibrate.
Enable app notifications and run a cycle. Check that running and completion states match what the machine actually does. Repeat calibration if needed.
Start with placement, connectivity and calibration. Most setup issues begin with one of these.
Charge the device, enable Bluetooth and the requested app permissions, and move the phone closer. Check its screen says PAIR ME. If not, open its menu and choose Pair phone, or Pair new phone and hold to confirm.
Confirm the network is 2.4 GHz, recheck the password, and verify the signal reaches the laundry room. Guest network restrictions can prevent a connection.
Check the sensor has not moved, inspect its charge, verify Wi-Fi and phone notification permissions, and rerun calibration for that machine.
Loads under 10 minutes on a dryer (8 on a washer) are ignored on purpose, so a bump or the machine next door can’t set off a false alarm. For a quick touch-up or a short dry, use the quick timer: hold the sensor’s button when you start the machine.
Press means a short press. Hold means keep it down about a second, until the bar fills. The first press just wakes the screen (WASHER or DRYER, battery, and READY, RUNNING or DONE). Press again to open the menu. In the menu, press to move to the next item and hold to choose it: Mark as done (while a load is running), Start timer, Calibrate (or Recalibrate), Pair phone (or Pair new phone), Check for updates, Info and Back. Left alone for 15 seconds, the menu closes and the screen goes back to sleep.
On the sensor, open the menu, choose Pair new phone and hold to confirm. Then open the sensor in the app and tap Change Wi-Fi.
Press the button twice: the version is on the top line of the menu. It’s also under Info on the sensor, and under Health in the app.
Your phone needs to be nearby during Bluetooth setup. After that, the sensors send completion events over Wi-Fi, without the phone staying beside the machine. The one exception is the quick timer where there’s no Wi-Fi (see below).
An admin picks the minutes in the app: open the sensor, then Settings, then Quick timer. After that, hold the sensor’s button for a second when you start the machine, and everyone gets a done alert when the time is up. With the timer set to Off, a hold just wakes the screen.
Yes. Start the quick timer as usual with the LaundrySense app open on your phone nearby. When the sensor can’t reach Wi-Fi, it passes the timer to your phone over Bluetooth, and your phone sends you the alert itself. You only get one alert, never two.
Yes. LaundrySense doesn’t listen for a chime at all. It detects a cycle from vibration: shaking means running, and a stretch of stillness (longer for a washer, so rinse pauses don’t count) means done.
Yes. Save each machine once: open the sensor’s settings in the app and tap Save as a machine, or New machine to calibrate it on a different one. Then use Switch machine whenever you move the sensor, and it picks up that machine’s calibration with nothing to redo. It’s made for laundromats, where your favourite washer might be taken.
A fan, a dehumidifier or a neighbour’s machine can keep a sensor feeling “running”. If a load runs past 3 hours, the app asks whether it’s still washing, and your answer teaches the sensor what to ignore. After 4 hours the sensor stops the run by itself.
Households have an owner, admins and members. Everyone gets alerts and can move loads. Admins add, rename, lock and remove sensors and set reminders. The owner looks after the plan and who’s an admin. For sensitive steps, like removing a sensor or changing roles, the app asks for your personal 6-digit PIN. Once you’ve confirmed on a phone, Face ID or a fingerprint can stand in for it there.
Each sensor is locked to its household. An admin opens the sensor’s settings in the app, taps Unlock for 15 minutes and confirms it’s them. The other household then has 15 minutes to add it.
LaundrySense sleeps between quick vibration checks and only turns on Wi-Fi when it has something to send, which stretches each charge. Battery life depends on how many loads you run and your Wi-Fi signal. The app shows each sensor’s battery level and lets you know when one drops to about 15%. Recharge it with any USB-C cable.
Tell it. On the sensor, choose Mark as done to send the alert right away. In the app, tap Not right? and pick what happened, like “It’s already done” or “It isn’t running”. The sensor adjusts its settings for that machine, within the range its calibration allows. You can reset what it learned from the calibration screen.
No. LaundrySense detects cycles from vibration only. It doesn’t record or upload audio.
The LaundrySense app is free for iPhone and Android. Download it, create your account, and tap Add device to set up each sensor. Prefer email? Turn on email alerts from your account page on the web.